Market

Why tank corrosion work is rarely tendered separately

Read enough tank corrosion tenders and a pattern appears: the subject is almost always "anti-corrosion works", "anti-corrosion application" or "derusting and painting". You rarely see "anti-corrosion coating supply". That is not ignorance on the buyer's part — it is the opposite. Separate out the paint and, when something fails, applicator and supplier point at each other.

Tenders in this trade fall into four tiers, and each has its own scale, entry barrier and route for the coating.

1. Whole tank or whole terminal: million-level, gated by qualifications and track record

Full corrosion protection of LNG terminal tanks or large crude tanks typically runs from one million to ten million. The first gate is not price but qualification: petrochemical construction contracting, specialist anti-corrosion and insulation contracting, safety production licence — miss one and the bid is rejected.

The second gate is track record, and it is specific: same medium, same capacity, last three years, minimum single contract value. I have seen requirements for main-body protection of crude tanks of 100,000 cubic metres or more per tank, which eliminates nearly every small and mid-sized crew.

Where does the coating enter? Usually in the technical schedule under principal materials: a named brand range, or "or equivalent". That positions the supplier as a package material vendor, and to get in you first have to be on the applicator's approved supplier list.

2. Local repair: hundred-thousand level, brands written into the specification

Partial derusting and coating of roof plates and shell plates, or floating roof overhaul, usually lands in the hundred-thousand range. This tier is the most interesting: it is neither pure material purchase nor a large project, but application with material included.

Here the technical schedule often names recommended brands, sometimes down to the grade. The reason is practical: the client usually owns the tank, has a record of what was applied, and wants the repair to be compatible with the existing coating. The brand clause is not exclusion, it is a clumsy way of stating a compatibility requirement.

The opportunity for a supplier is to translate that for the client: turn "use brand X" into technical conditions — same family, same pigment system, comparable solids, adhesion to standard, demonstrable intercoat compatibility. Whoever can supply that evidence earns the right to discuss substitution.

3. Single points: under a hundred thousand, one round of enquiry

External protection of supply stations, filling stations and small tanks often falls under a hundred thousand. These go to enquiry or direct award, with short cycles, fast decisions and the highest price sensitivity.

Paint is a larger share here because there is little scaffolding or labour. It is also the messiest tier: quotes can differ by a factor of two, and the difference is rarely the brand — it is whether surface preparation grade, film thickness and old coating removal are specified at all.

My habit when quoting this tier is to tabulate surface preparation, number of coats, thickness, and whether tax and freight are included, so the client can compare across suppliers. Without that, every quote gets dismissed with "someone else is cheaper".

4. Campaign treatment including equipment: equipment leads, paint follows

Steel structures and piping campaigns in steel mills and chemical plants run from one to ten million and cover more than steel — air coolers, heat exchangers and pipe supports are included.

Evaluation is normally points-based, with price often weighted at only about half; the rest is track record, method, staffing and programme. Lowest price does not guarantee award. I have seen the top-ranked candidate priced slightly above another on the same shortlist, which shows price is not the only variable.

Paint here is either supplied under the client's framework agreement or purchased by the winner subject to brand approval. Entry comes from being in the client's or contractor's brand library in advance, not from cutting price at the last minute.

5. One more line is moving: the standard

The technical standard for corrosion protection of steel petroleum tanks is under partial revision for public comment. Such revisions typically affect the recommended coating schemes, the wording of surface preparation grades, how inspection lots are divided and what is tested at acceptance.

When the standard moves, designs in progress and contracts already signed develop a gap in interpretation. That is an opening for a supplier: whoever sets out the differences between old and new versions clearly gets to speak at the technical clarification meeting.

I usually prepare a one-page comparison: what the new version adds, whether existing schemes still comply, which tests need adding. That page is worth more than a product brochure.

6. So where is the coating business

Across the four tiers the conclusion is blunt: tank coatings are not sold to the owner, they are sold to whoever is qualified to bid. Whole tanks depend on the applicator's supplier list, local repair on compatibility evidence, single points on clarity of quotation, campaigns on the brand library.

Watch only for the words "coating supply" in tender notices and you will wait a year for a handful. Follow the applicator's projects instead: individual orders are smaller but repeat business is steady. The money in this trade is not in the tender, it is in the relationship.

Need selection advice?

Tell us your substrate and service conditions

One-to-one coating consultancy: system design, quantity take-off and quotation.

Contact us
WhatsApp