Ask a supplier how long delivery takes and the answer is usually 'a few days if it is in stock'. What the site is waiting for is not dispatch but a pail it can open and apply. Between the two sit three separate stages.
Export shipping differs from domestic not in freight but in paperwork and the boundary of responsibility. Coatings are dangerous goods — one missing packing certificate or an out-of-date SDS and the cargo stops at the port.
Dew point often collapses into one line: humidity is under 85%, so spray. What decides the outcome is how readings are taken, how the margin is calculated, and where steel temperature goes in the hours after coating.
Reverse the order and acceptance day looks fine; a year later the system lifts in sheets. Then the fire-protection crew blames the primer, the coatings crew blames the intumescent, and the owner pays. What saves money is not a better paint but a documented sequence and a compatibility statement.
'Or equal' is the shortest phrase in a specification and the easiest way to lose a bid. Handled well it is room to manoeuvre; handled badly it means a rejected substitution and a stalled schedule.
For the same square metre of tank protection, the buyer of the paint may be a completely different party. Domestic overhauls put coating materials under contractor supply, so the buyer is the applicator's procurement team. Overseas EPC splits painting out as a separate package, so the buyer becomes the subcontractor. New-build coatings often sit inside an EPC framework agreement. Knowing which layer you are in tells you who to call.
Technical specifications often carry the phrase "brand X or equivalent". Those three words open a door to substituting a grade, but they are not permission — they shift the burden of proof onto whoever wants to change. Most substitutions fail not because the product is inadequate but because the evidence was never assembled.
One extra day in dock usually costs more than the whole ship's paint. And the commonest cause of that day is a topcoat applied on the last afternoon into rain.
"Zinc-rich primer" is four words on a requisition, and both epoxy zinc-rich and inorganic zinc silicate answer to them. Yet the two differ completely in curing conditions, overcoating requirements and temperature rating, with prices thirty percent apart. Choosing wrong rarely costs you in paint; it costs you in programme and rework.
The most counter-intuitive fact in the workshop: the drier the air, the slower inorganic zinc cures. Crews blame the paint; it is the curing mechanism.
Tank corrosion protection is almost never tendered as a paint purchase on its own. The coating travels inside the application contract or sits in the main contractor's technical schedule. The reason is simple: the work content is in surface preparation and scaffolding, not in the material, and separating out the paint breaks the chain of responsibility. Understanding that tells you where the coating business actually sits.
Both get called 'little bumps' and they require opposite treatments. Pinholes are filled inward; blisters are cut out entirely. Misdiagnose and the work is wasted.
A common idea on an industrial site is that steel is steel, so one system across the whole plant is the simplest route: one bill of materials, one batch, one mobilisation. It does save procurement and briefing effort. But at least three categories of asset on that site fail differently and cost differently to repair. Blanketing them with one system spreads the risk of the most expensive ones across everything.
'One thick coat saves labour' is the most expensive saving on a coating site. Once a crack reaches the substrate, the protection is gone and the repair costs more than doing it properly.
When an epoxy floor lifts, the first instinct is to blame the paint. Open it up and the failures cluster at edges, doorways, around equipment plinths and beside joints. What those places share is not the coating but the moisture content, strength and levelling of the substrate. The paint is simply the layer that gets pulled off last.
Visually clean steel can still carry an invisible salt layer. It does not block adhesion; it absorbs moisture under the film and lifts the paint from beneath months later.
"Blasting cannot reach this area. Can we go St3 and put zinc-rich straight on?" It is the most common question in repair yards. The answer is yes, provided everyone understands where St3 falls short, or five years later you will open up rust rather than a film.
Epoxy topcoat is inexpensive, bonds well and resists chemicals, but it has one weakness that cannot be formulated away: it is not UV stable. Outdoors it chalks and loses gloss within months and looks dull within a year. Polyurethane topcoat, cured with an aliphatic isocyanate, holds gloss and colour for five to eight years. Behind those numbers is chemistry, not formulation skill.
The common winter misjudgement: touch-dry, so it must be ready to recoat and use. At low temperature epoxy is only falsely dry; crosslinking is far from complete and performance can be half the design value.
PPG has issued a product change notice for SIGMACOVER 380, the general-purpose pure epoxy primer: the grade is being phased out and replaced by SIGMAPRIME 700 HSV. For projects currently using it, this is not simply a change of name — the scheme, overcoating intervals and certification scope all need re-checking against the new product.
The PSPC text looks highly specific: surface preparation, profile, salt level, 320 micron DFT, light colour, inspector qualification, coating technical file. Many projects therefore treat it as a checklist and consider compliance achieved once every box is ticked. The real problem is that a coating which passes the boxes does not necessarily last 15 years.
The same number means different things: failure in the adhesive is a test problem, between coats a system problem, in the substrate a concrete strength problem. Without the failure plane, the figure means nothing.
Theory says twenty litres covers a hundred and sixty square metres; in practice you run dry at a hundred and twenty. The first reaction is a short fill, but with the formulation sheet open the shortfall usually comes from three places: the wrong solids figure, no loss factor, and roughness treated as zero.
"Does this count as Sa 2½?" is the most argued sentence in protective coating work. Each side holds up a phone photo and neither convinces the other. Judgement actually has a defined method resting on four things: the comparator, profile depth, soluble salts and surface dust. The first three have instruments, the fourth has a tape method, and all four leave a record.
The usual mistake is assigning by industry: chemical plants always C5, warehouses always C3. The category depends on how much rain and salt a specific location sees in a year.
Coating failures cluster in winter and the wet season, and the cause is usually a narrower application window against an unchanged schedule. Three readings decide whether work proceeds: steel temperature, dew point and relative humidity.
In technical discussion alkyd is treated as obsolete; everyone talks epoxy, polyurethane and fluoropolymer. Yet on real maintenance sites alkyd still moves large volumes. Not because it performs well, but because under certain conditions it is the best value: single pack, brushable, tolerant of old coatings and cheap.
Temperature ratings are almost always continuous service. Equipment actually sees heating and cooling cycles. Treating a peak as continuous can halve film life.
The principle of glass flake coatings is easy to grasp: thin glass platelets lie parallel within the film, so any medium permeating it has to travel around platelet after platelet, extending the path many times over. That makes it genuinely strong in immersion and chemical service. The problem is that it is often specified where it is not needed, and badly applied where it is.
Many projects treat a hygiene approval as the finish line. It only shows the formulation is harmless; the water test before commissioning decides whether the tank is usable.
The most common situation in dry film thickness inspection: the average is on target, the report says pass, yet a handful of individual readings sit at sixty percent of the specified value. Judged by average it passes; judged point by point it fails. The difference is not the instrument but which set of rules applies — and that has to be settled before work starts.
'Acid and alkali resistant' is meaningless in lining selection. 30% sulphuric acid and 5% hydrofluoric acid, ambient alkali and 80 °C alkali have different answers.
The commonest mistake in antifouling selection is treating "years" as the only criterion. Two products both rated for five years can save fuel on an ocean-going ship and fail within two years on an inland vessel. What decides it is not film thickness but the operating profile: speed, activity ratio, idle time and water temperature.
Galvanising is smooth, chemically inert and carries an invisible film of oil and zinc oxide. Coat straight onto it and whole areas detach in three to six months.
Applying a steelwork topcoat to concrete usually blisters and lifts within six months. Not a bad paint — two substrate properties force a different system.
Water jetting means no dust, no sparks and it removes salt. Its critical limitation: it creates no profile. That single difference decides where it can be used.
Everyone knows the minimum; overrun it and you get lifting. The maximum is routinely ignored, and overrunning it does not lift — the next coat simply fails to bond, invisibly.