Epoxy vs inorganic zinc-rich primer: how to choose
I once saw a structural steel painting schedule: epoxy zinc-rich primer, micaceous iron oxide intermediate, aliphatic polyurethane topcoat, twenty-odd tonnes. Every product named, not a single grade number. At quotation stage nothing looks wrong; on site you discover three possibilities — what arrives is a low-zinc "zinc-containing primer", or inorganic was chosen for temperature but the sealer coat was left out of the price.
The boundary between these two primer families comes down to four points. Work through them in order and you will rarely choose wrong.
1. What drives the cure: this decides whether you start on time
Inorganic zinc silicate cures on atmospheric moisture, not on a metered hardener. That imposes a hard environmental requirement: below roughly 65% relative humidity it will not cure properly, and some products demand more. Northern winters, dry indoor shops and aggressively ventilated blast halls are its difficult conditions.
Push humidity the other way and you get the opposite problem: cure too fast, dusty surface, poor adhesion. The application window for inorganic zinc is therefore much narrower than for epoxy, and moisture curing or fogging is often needed. On a tight programme with uncertain weather, this alone can rule it out.
Epoxy zinc-rich is a two-component chemical cure. The hardener is metered, reaction slows at low temperature but can be managed with heating or extended intervals, and the conditions are those of any conventional epoxy. That is why the great majority of structural steel projects default to epoxy zinc-rich: not better performance, easier to cure.
One trap worth flagging: inorganic zinc is ruined by water before it is fully cured, so rain on the day of application is a disaster. The programme has to leave a weather window.
2. What goes on top: leave a line for the sealer coat
An inorganic zinc surface is a porous zinc layer. Applying epoxy intermediate directly gives pinholes and blistering, for a simple reason: air in the zinc porosity expands under the coating, and there is an alkaline reaction between zinc and the following coat. Correct practice is a mist coat of epoxy sealer to close the porosity before the intermediate.
That sealer is regularly missing from the bill. It is not expensive per litre, but it adds an operation, a drying interval and a mobilisation — all of which count against the programme. Some data sheets say "epoxy sealer or direct overcoat", which assumes a penetrating intermediate plus a mist transition layer: still two operations.
Epoxy zinc-rich has no such issue. The surface is tight and the intermediate goes straight on; the only concern is zinc salts. A zinc-rich primer exposed in damp conditions develops white rust, and it must be washed with high-pressure fresh water and dried before overcoating, otherwise the whole area blisters. That applies to both families, but inorganic is more sensitive.
For primer left outdoors more than a month without overcoating, I ask for washing, drying and an adhesion spot check before deciding whether to overcoat directly or abrade.
3. Temperature and solvent resistance: where inorganic earns its price
Continuous service temperature for epoxy zinc-rich is typically in the 120 to 150 degree range; above that it degrades, because the epoxy resin itself is not heat resistant. Inorganic zinc silicate goes to 400 degrees and beyond, and resists solvents and oils. That is why it is irreplaceable on tanks, piping, flues and cracking units.
Two concepts need separating: the temperature on a data sheet is often a peak or short-term tolerance, not a continuous service limit. Design temperature, start-stop frequency and thermal cycling all push the usable tier down. Selecting against the peak figure is the most common error in these projects.
The other overlooked factor is welding and cutting. Plate pre-primed in the shop gets welded, and zinc vaporises under the arc, producing fume that affects weld quality and operator health. Shop primers are therefore usually low-zinc or weldable rather than high-zinc — the opposite of the "more zinc is better" instinct.
4. Zinc content and film thickness: do not read the percentage alone
Ask how zinc content is measured: metallic zinc by weight in the dry film, by volume, or zinc powder loading in the formulation. The same product can be quoted three ways. The international convention is dry film weight, where inorganic zinc usually exceeds 80% and epoxy zinc-rich sits between 70% and 80%.
Film thickness matters too. Inorganic zinc cracks when applied too thick, especially at edges, so 50 to 75 microns is typical and you cannot compensate coverage by adding thickness. Epoxy zinc-rich can run 75 to 100 microns with more tolerance.
One criterion often used that does not hold: component count. Both families are mostly two-component, but three-component inorganic zinc exists, with liquid, powder and catalyst packed separately. Reading "three components" as proof of inorganic is not sound.
5. How to decide
My order of judgement: first, is there a temperature or solvent requirement — if so, inorganic, if not, carry on; second, look at programme and season — if humidity cannot be reached or the schedule is tight, epoxy; third, consider whether the asset can be recoated — high-value, hard-to-access items such as towers, stacks and tank internals justify paying for inorganic life.
Cost it as a whole: inorganic carries a higher unit price, an extra sealer coat and a narrow window, but delivers life and temperature tier. For ordinary structural steel in ambient atmosphere, epoxy zinc-rich with MIO intermediate and polyurethane topcoat routinely achieves 15 years plus in ISO 12944 C4 or C5, and there is no need for inorganic.
Writing only "zinc-rich primer" is the most expensive omission in this kind of project. Specifying the family, the basis of the zinc figure, the thickness range and whether a sealer is required saves far more than arguing three percent on unit price.