Antifouling: the real difference between SPC and CDP
Antifouling is the most match-dependent coating on a ship. It suppresses settlement either chemically, through biocide release, or physically, through surface properties, and the way organisms settle varies completely with water body, temperature, speed and idle time.
So the first step in selection is not the product catalogue. It is understanding how the vessel operates.
1. Three families with different mechanisms
Self-polishing (hydrolysing): the resin hydrolyses slowly in seawater, releasing biocide layer by layer and renewing the surface. Suits vessels in continuous service at higher speeds. The key parameter is polishing rate in microns per month, which must match the docking interval.
Contact or insoluble matrix: the resin does not hydrolyse and biocide leaches slowly from within. Suits slow vessels, frequent port calls or long stationary periods. The drawback is a spent, spongy leached layer building up on the surface, which eventually impairs performance.
Foul release (low surface energy, silicone or fluoropolymer): no biocide; an extremely low surface energy prevents firm attachment and the flow of water removes organisms underway. Suits fast, high-activity vessels and waters with environmental restrictions. It does not work when stationary — long idle periods produce heavy fouling that cannot be scraped off.
The three fail in completely different ways and mixing them up is expensive. A foul-release coating on a vessel with fifty percent annual activity buys a solution that does nothing while the ship sits.
2. Four parameters decide the choice
First, speed. Self-polishing products need shear from water flow to maintain polishing; prolonged slow running means insufficient polishing, excessive thickness and eventual large-scale detachment. Foul release also needs flow and is usually designed for higher speeds.
Second, activity ratio: the proportion of the year underway versus stationary. Long stationary periods favour contact types; high activity favours self-polishing for fuel savings. The owner has this data — ask for it rather than accepting "she runs pretty much all the time".
Third, trade and water temperature. Tropical waters carry heavy fouling pressure and require a higher release rate; temperate or cold waters allow lower. A vessel trading across zones should be specified for the most severe.
Fourth, docking interval and total thickness. Antifouling life is essentially total biocide divided by release rate. To reach five years, check whether release rate times months stays within usable thickness. Many projects skip this arithmetic and run out at three years.
3. The scheme matters more than the product
Antifouling needs a sealer or tie coat beneath it, to prevent solvent or biocide in the antifouling from reacting with the anticorrosive below, and to provide adhesion. Omit this and the result is wholesale detachment.
Old coating condition is equally decisive. If the previous coat was contact type, the leached layer must be fully removed, usually by sweep blasting or high-pressure water, otherwise the new coating keys to a spent layer and adhesion is illusory. If the previous coat was self-polishing, cleaning and light sweeping usually suffice.
One frequently overlooked point: antifouling must not be applied too thick. Excess thickness raises internal stress, produces uneven polishing and can crack. Total thickness follows the product data sheet; "a bit more for safety" is not a strategy.
4. Environmental regulation is changing the options
Organotin antifoulings were banned long ago and that is not in dispute. The argument now concerns restrictions on biocides, with some regions and ports imposing additional requirements on specific substances.
Silicone foul release attracts attention largely because it does not rely on biocide. But its conditions are strict: high speed, high activity ratio and acceptance of a higher initial price. On a vessel that does not meet those conditions it costs more, because failure means docking and full re-treatment.
The practical sequence is to screen out inapplicable families by operating profile first, then compare compliance and cost within what remains. Reverse the order and you fall into the trap of concluding that all green products are expensive.
5. How a real case looks
Take a 50,000 tonne bulk carrier, seventy percent annual activity, 13 knots, trading Southeast Asia to the Chinese coast, five-year docking interval.
The profile is moderate speed, relatively high activity, warm water. Self-polishing is the reasonable choice, but at 13 knots the polishing rate must be adequate — a product with too low a release rate ends up with excess thickness and reduced adhesion after five years.
Change the trade to inland waterways or frequent long anchoring and self-polishing no longer fits; contact type takes over. Same tonnage, same five-year docking, completely different product family.
The point of the example is not which product is better. It is that one "five year" requirement can point to entirely different schemes. That is why quoting a single grade is not useful.
6. What to ask before quoting
For this kind of quotation I ask five questions: vessel type and tonnage, design speed and actual average speed, annual activity ratio, main trade and water temperature, and docking interval. Those five answers essentially fix the family.
Then two execution questions: what family was applied last time, and what surface preparation is achievable, sweep blasting or high-pressure water. Those fix the scheme and the application method.
Only then is a quotation meaningful. A single grade and a total price give the client nothing to judge, and leave you exposed later — because the scheme itself may not have been applicable.