Epoxy floor peeling: check these three substrate factors first
A workshop floor of over a thousand square metres starts to drum at the doorway three months after handover. It sounds hollow underfoot; pry up a piece and the back of the epoxy is clean while a thin skin of concrete comes away with it. The failure interface is unambiguous: the break is not inside the film but in the top few millimetres of concrete.
So the investigation runs bottom-up. Confirm the concrete is dry, then that it is sound, and only then look at levelling and priming. The coating grade comes last.
1. Why failures start at edges and doorways
Epoxy is thermosetting: it shrinks as it cures and expands and contracts with temperature in service. The middle of a large floor is restrained on all sides, so stress can only release at free edges — doorways, saw cuts, equipment plinths, drain surrounds. Those are the pressure relief points.
The same square metre that lasts ten years in the centre can curl within one year at the perimeter. That is not the applicator favouring one area; it is a difference in boundary conditions. When you see edge lifting, do not just patch the edge — assess how much bond remains across the whole field.
The correct repair is to cut back to sound material in a square, grind a taper and rebuild the transition. Painting a band along the lifted edge will fail again within six months because the stress has not gone anywhere.
2. Moisture: 28 days buys strength, not dryness
Everyone knows concrete needs curing, but curing serves the hydration reaction. How much water remains in the capillaries is a separate question. Enclosed workshops, basements and the strip along an external wall dry slowly; the surface looks pale and feels dry while moisture content may still sit at six or seven percent.
Two field checks are practical. The plastic sheet method: seal roughly one square metre of polythene on the floor for at least 16 hours; condensation on the underside means moisture is still migrating. Or take a reading with a moisture meter or the calcium chloride test (ASTM F1869). For self-levelling epoxy, 4% is a common ceiling, but the actual limit belongs to the product data sheet — formulations differ in tolerance.
A rule of thumb for new concrete is about one week of drying per 25 mm of thickness, so a 100 mm slab needs roughly a month — in warm, ventilated conditions. Below grade, or on a ground slab with no damp-proof membrane, waiting longer will not get you there. Either install a barrier or switch to a system that tolerates moisture. Forcing epoxy onto a wet slab is a bet, not a method.
3. Strength and surface prep: not every floor can be shot-blasted
Shot blasting strips laitance by impact, which presupposes the substrate has strength. On a dusty floor below C20, the machine chews through the surface, exposes aggregate and leaves powder underfoot. That is not an equipment fault; it is a mismatch between substrate strength and preparation method.
The test is crude but effective: score the surface with a screwdriver. If it cuts a clear groove and sheds powder, the floor needs consolidation first. Where possible, run a pull-off test (ASTM D4541) and look at where the failure occurs. If the concrete itself breaks rather than the bond line, the substrate is the weak link and any coating sits on thin ice.
The right sequence is scarifying or grinding off the laitance, filling hollows, and where necessary applying a polymer-modified mortar to build strength — before any discussion of coating. Sealing a loose surface with primer simply wraps a layer of friable material inside the system, and it will travel as a sheet once loaded.
4. Levelling: why cement mortar screed was dropped
GB 50212-2014 dropped cement mortar screed from the recommended build-up, and the commentary is unusually blunt: levelling with cement mortar has caused many failures of protective layers, particularly in light-duty monolithic construction.
The mechanism is not hard to follow. Cement mortar screed has low strength, high shrinkage and bonds through a thin slurry skin, so it debonds easily on its own. Seal it with epoxy and moisture can no longer escape upwards, so it pushes down and lifts the weakest interface. That is why lifted plates often bring the screed with them.
Current practice is polymer cement mortar for local flattening only, not a full-layer screed, or an epoxy mortar that acts as both levelling and primer. The money saved on a full cement screed comes back many times over at repair stage.
5. The repair bill is not in the paint
Cost this properly. Milling off cured epoxy is priced by the square metre for machine and labour; add removal, substrate re-preparation, curing, re-coating and the days of lost production, and that is the real number. Paint is the smallest line in the contract yet the first place people look to save.
Procurement can only do so much: write substrate requirements into the technical specification, require moisture and pull-off data before application, and agree in the contract who pays for out-of-spec substrate and how it is measured. Those three clauses save more than shaving five percent off the coating price.