Can a specified coating grade be substituted? Pass three checks first
Let us be clear about one thing: substitution is not a question of whether you may change, it is a question of who carries the liability. Someone willing to carry it will do the comparison, make the test panel and get the signature. Someone who is not will say "it is the same thing, both epoxy".
There are three gates on this road and the order matters.
1. First gate: read exactly what the specification says
Brand clauses come in three forms and each is handled differently.
Named brand: a specified brand and grade with no "or equivalent". Do not touch it without written client consent. A verbal "use your judgement" counts for nothing at acceptance.
Brand plus "or equivalent": the open form. Note that the burden of proof is yours, not the client's. You submit the comparison and the panel report; you do not wait for the client to prove you wrong.
Performance criteria only, no brand: the freest form and the easiest to get wrong, because the criteria are often incomplete — adhesion and salt spray listed, solids, chemical resistance and thickness range missing. Fill the gaps by application and record the reasoning in the technical clarification.
There is a fourth case: clauses requiring original manufacturer product or refusing agents. Those exclude traders outright and are outside the discussion. Recognising that sentence early saves a lot of wasted effort.
2. Second gate: compare data sheets field by field
Equivalence is not asserted, it is demonstrated field by field. Put the two data sheets side by side and read these:
Type and cure mechanism: epoxy, polyurethane and inorganic zinc silicate are different materials. Within epoxy, amine-cured, polyamide-cured and phenolic epoxy are not interchangeable either.
Volume solids or non-volatile content: this determines how many litres reach a given thickness and drives both consumption and VOC. Five points lower means five percent more material, at least.
Density: affects coverage per square metre, wet-to-dry conversion and freight.
Recommended thickness range and number of coats: a product that reaches 100 microns in one coat and one that manages 60 are two different systems.
Chemical resistance table: the field most often glossed over. It must state the medium, concentration, temperature and whether immersion or spillage. "Resists acid and alkali" means nothing.
Overcoating intervals, minimum and maximum: on a tight programme, a short maximum interval forces the site to rush.
VOC and local limits: some projects carry hard environmental permit constraints.
If a key figure is clearly lower — zinc content, solids, temperature rating — that is not equivalence, it is a downgrade. A downgrade can be negotiated, but negotiate price and liability as a downgrade, not disguised as equivalence.
3. Third gate: test panel plus signature, or the swap is worthless
If the fields match, there is still site verification. The panel procedure must be defined: surface preparation grade (Sa 2½ by blasting, medium G profile per ISO 8503), thickness, curing conditions and the tests to be run.
Run at least three tests: adhesion (pull-off or cross-cut), intercoat compatibility on the actual system rather than standalone, and appearance plus cure — any blistering, blushing or tackiness. For repair work, add compatibility between old and new coating.
The signature is what matters. The panel report should be confirmed by client, supervisor and applicator, with date, location and batch recorded. An unsigned panel is the same as no panel: when something goes wrong, anyone can claim it was only a trial.
The neatest approach I have seen: bind the comparison table and panel report into a single sheet, sign it in the technical clarification meeting and attach it to the minutes. That sheet outperforms ten verbal conversations.
4. Three places people come unstuck
First, treating "both epoxy" as equivalence. Epoxy is a family: hardener type, solids and pigment system all differ. Using a conventional epoxy to replace a phenolic epoxy in solvent service looks fine at first and blisters in three months.
Second, comparing unit price only. A substitute 20% cheaper with 20% lower solids costs the same per square metre, plus an extra coat and pass of labour. Include consumption, not just drum price.
Third, starting work with no record. This is the most common and the most expensive: the swap is made, the work looks good, and two years later the client produces the original specification and says the grade was changed. With no signed document, the liability sits entirely with the supplier.
One more detail: colour can shift slightly after substitution, especially whites and light greys. Confirm the shade difference is acceptable before bulk supply, not after two panels are side by side on the wall.
5. What I do
My substitution proposal is a single page: original grade on the left, alternative on the right, six key fields compared in the middle, and one line of conclusion — equivalent, downgrade acceptable subject to client approval, or not equivalent and not recommended. The panel arrangement goes at the bottom.
The advantage is that it returns the decision to the client while drawing a clear liability boundary. If something goes wrong, that page shows what was said at the time, which beats any amount of explanation.