MODEL DATA

FFM180

Brand3TREES
ModelFFM180
CategoryPolyurethane topcoat

FFM180 is a Polyurethane topcoat from 3TREES. This page groups model identity, system position and the data request entry so you can verify the full system before enquiring.

Key technical data

Volume solids68 ± 2%
Dry film thickness50–100 µm
Theoretical spreading rate0.15 L/m²
VOC230 g/L
Density / specific gravityApprox. 1.52 kg/L (white; other colours vary slightly)
Number of componentsTwo-component
Mixing ratioBase FFM180A: curing agent FFM180B = 7.7:1 (by volume)
Colour / appearanceWhite / customer-specified colours

The technical content below is reproduced in English as published by the manufacturer; terms, grades and values follow the English original.

How this coating class protects

Polyurethane topcoats rely on the urethane linkage formed when an isocyanate hardener reacts with a hydroxyl resin, which puts weathering and gloss retention at the top of the normal topcoat range. Two sensitivities come built in: the hardener dislikes moisture, and the recoat window is narrow. Both make it far less forgiving on site than epoxy.

What to verify in the original TDS

These are checking criteria, not numeric commitments. Every figure follows the current original TDS.

  1. Aliphatic or aromaticAliphatic does not yellow and suits exterior and light colours; aromatic is cheaper, weathers poorly and yellows outdoors within months. The data sheet must say which, not merely polyurethane.
  2. Hardener ratio and pot lifeThe ratio is stoichiometry, not a suggestion. Over- or under-dosing gives poor cure or brittleness. Pot life sets how much you mix at a time.
  3. Recoat window, minimum and maximumNarrower than epoxy. Past the maximum, intercoat adhesion has to be restored by abrasion.
  4. Minimum application and curing temperatureReaction rate collapses at low temperature, so products set a floor below which you do not apply. The figure differs by product; read the sheet.

Application control points

Keep hardener containers sealed and mix full units

Isocyanate reacts with atmospheric moisture; an opened can skins over and loses activity. Decanting into small cans creates more problems than it solves.

Do not leave the interval overnight if you can avoid it

Windows exist to give chemical plus mechanical bonding. Coating the next morning means relying on abrasion, which is inferior to recoating inside the window.

Light and dark colours need different thickness discipline

Light colours hide poorly, so crews build thickness to cover and overshoot the spec. Tint the primer or add a coat instead.

How to settle site disputes

Gloss loss and chalking mistaken for a defect

Under strong UV and acid rain, gloss loss is normal ageing. To judge premature failure, compare against exposure time and neighbouring areas, not against the presence of chalking.

False cure from moisture-contaminated hardener

Dry on the surface, soft underneath, fingerprints on pressing. Check ratio and storage before blaming the paint.

Common questions on this coating class

Can polyurethane go straight onto zinc-rich primer?
Generally not recommended. The zinc surface is porous and alkaline, and direct topcoating blisters. An intermediate coat is standard unless the manufacturer explicitly lists a direct system.
Is aromatic polyurethane acceptable indoors?
Indoors without UV, yellowing is not visible and it can be used. Where daylight carries UV, aliphatic is still the better choice.

The above gives class-level technical requirements and judging methods. Specific values and systems follow the current original TDS and the project specification.

Place in the coating system

Typically used as a topcoat for colour, gloss and weatherability; primer and intermediate are selected separately to suit the exposure.

Need the original TDS or a quote for this model?

Send the model, quantity, destination port and service conditions — we reply with a complete coating system, not a single can.

← 3TREES Back to product catalog →
Need selection advice?

Tell us your substrate and service conditions

One-to-one coating consultancy: system design, quantity take-off and quotation.

Contact us
WhatsApp